Antares Temperature control

Wordt gewoonlijk geïnstalleerd in de aanvoerleiding wanneer de tank hoger gelokalisserd is dan de brander. Vertikale montage, 230 V - 50 Hz, N.C. Interne diameter 8 mm.

B.056

Elektroventielconnector volgens DIN 43650 standaard.

For solenoid valves Art. H.500 or coils Art. H.501

C.051

Thermostatic mixer for the distribution on systems for domestic water. Temp. Max:85°C

C.053

Thermostatic mixer for hot water distribution systems, with extractable cartridge, filter and chrome plated knob with blocking switch.

Control range 20° / 65°C.

C.055

Thermostatic mixer to fit in wall for shower box with d.46 rose and blocking switch and non return valve.

Connections :1/2´M x 1/2´M x 172´F. Flow rate lt/min. 3bar:29.

C.056

Sicherheitsvorkehrung Antiverbrennung in verchromtes Messing. ½“ IG x ½“ AGVerhindert die .

Unfallgefahr von Verbrennungen durch zu warmes Wasser. Leistung lt/min. 3 bar: 29

C.060

Threaded thermostatic mixer for centralized hot water systems.

Bronze body. Max pressure 100 bar Minimum flow 34l/min Control range 38-55°C Conn.F

C.065

Thermostatischer Mischer für Solaranlagen mit Verteilung von Warmwasser mit hohen Temperaturen bis 100°C. Regulierung: 30°C - 65°C. Mit eingebautem Reserveventilù

Entwickelt für Solaranlagen für sehr hohe Temperaturen um die 100°C

C.067

Automatisches thermostat. Verteilerventil für Sanitärwasseranlagen des Solarspeichers zum Kesse der kontrolliert, sollte die Temperatur unter 45°C sinken.

Festeinstellung bei 45°C - Höchsttemperatur max 100°C.

C.069

Regulier Kit für Solaranlagen. Zusammengesetzt aus Umleitungsventil (Art. C.067) und Mischventil (Art. C.065). Temperaturregler 30-65°C.

Designed for solar thermal heating to divert fluid path according to the instant temperature and supply an adeguate adjustment of use. Connections with fittings 3 pieces M. on valves and output M. Pre set to 45°C.

E.140

4-Wegs kruisvormig draadmengventiel in gietijzer F.

E.141

3-Wegs draadmengventiel in gietijzer. V. koppelingen.

E.142

4-Wegs kruisvormig mengventiel in gietijzer met flens. Zware uitvoering.

For the connection counter flanges see models PN6 -UNI 2253 and UNI 2276.

E.143

Brass three way mixing valve with by-pass pump conn. 1 1/2´F Flow kv10.

Connections: 1 1/2´ F. sw. x 1 1/2´M. x 1´ M. Motorized with servomotor Art- T.109.00.

E.144

3-Wegs gietijzeren mengventiel met flens.

For the connection counter flanges see models PN6 - UNI 2253 and UNI 2276

E.147

4 way thermostatic mixing valve, threaded and adjustable.

Control range. 30-60°C Indicated for temp. reduction of underfloor heating systems. Control adjustable with knob.

E.149

Thermostatic mixing valve for underfloor heating systems.

Körper aus gesandetem und verchromten Messing. Regelbereich: 20° - 50°C. Regelskala 1-5. Sehr klein, daher kann man den Mischer direkt vor den Verteilersammelleitungen einbauen, um die Temperatur der Fußbodenheizung zu senken.

E.150

Thermostatischer Mischer ´L´ in Messing für Fußbodenheizung und um die konstante Temperatur zu regulieren: 20°C-45°C

Für Anwendungen bei denen die Zugangs-/ Ausgangsrohre parallel sind.

E.154

Thermostatischer Mischer aus Messing aus 1” Antikondens für Rücklaufleitungen in den Kesseln für feste Brennstoffe. Regulierung: 45°C-75°C. Kompl. mit Thermometer.

Reguliert automatisch die Rückkehrtemperatur des Kessels (feste Brennstoffe) um sicherzustellen das die Temperatur nicht unter einem vorgegebenem Wert sinkt und erhöht die Effizienz des Kessels.

E.215

Anti condensation thermostatic valve for biomass thermal systems with prepared connections for the application of a pump. 1 1/2´M x 1 1/2´F x 1´M

Capacity 3,2CV Max pressure 10 bar - Max temp 100°C Preset valve 45°C (advisable for wood) 60°C (advisable for pellett).

E.220

Preassembled anticondensation circulation group for heat generators on solid fuel feed composed of dinamic anticondensation by-pass, adjustable circulation pump ´Modulex Hybrid´ high efficiency 6mt delivery, 3 interception valves with thermometer and check incorporated.

Model DN 25 for power upto 32 KW Connections: 1´ - Flow KV: 3,2

E.607

Basismodule bestaande uit thermostatische mengventielen voor temperatuurregulering (Art. T.133.10) geïnstalleerd op een modulair element met parallelle aanzuig- & retourkoppelingen 1 1/2´ M. boilerkant onderaan en 1 1/2´ V. wartelmoer bovenaan aan de systeemkant. Tussenafstand koppelingen: 125 mm - Hoogte: 110 mm. Compleet met een vaste aanpasbare by-pass voor boilercircuit bruikbaar wanneer de controlegroep is geïnstalleerd aan de boilerwand of op de boilercirculator. Het systeem voorkomt het

Aanpassingsschaal: 20°C - 70°C.

E.609

Special ´T´ joint for condensation alignments for the in/out flow of the mixing valves (T.133.50 E.215. E.143.12).

Terminal poles distance 90mm Connections 11/2´F x 11/2´M x 1´F

E.610

Pair of brass adapters for mounting DN25 1´1/2 M. Pump Groups on manifolds with different outlets.

E.613

Suction valve for “Multiflex” tank with pull lever and foot valve. In brass with 1 ”M connection

Aanzuig- en retourkoppelingen: diameter 8, 10, 13 of 3/8´. Lengte aanzuigslang: 2.200 mm. Met diameter 6 koppeling, klaar voor aanhechting van niveaumeter A.040.00.

E.614

4-Wegs kruisvormig mengventiel in gietijzer. Parallelle koppeling 1 1/2´ M. x 1 1/2´ V. wartelmoer.

Kan geïnstalleerd worden op boilerverbindingsstuk onderaan & systeemverbindingsstuk bovenaan.

E.621

Invertable relaunch assembly DN25, composed of 2 ball valves with thermometer and one way valve, high efficency adjustable circulation pump ´Modulex Hybrid´ 6mt delivery, alignment spacer and ball valve with screw-driver adjustment for eventual substitution of pump and isolation shell.

* For power up to 50 KW: predispoded for insertion of by-pass valve for eventual over pump pressure (Art. P.301.03).

E.623

Module DN25 for lowering and regulating thermostatic temperature at fixed point of : 30° - 60°C for systems with radiant panelscomposed of 2 ball valves with thermometer and one way valve, high efficiency adjustable circulating pump ´Modulex Hybrid´ 6mt delivery, 3 way thermostatic valve, alignment spacer, and ball valve screw-driver adjustable for eventual substitution of pump, safety thermostat manual reset for stopping pump in case of abnormalities and isolating shell.

* predisposed for insertion of by-pass valve for eventual over pump pressure (Art P.301.03).

E.624

Module DN25 for lowering and regulating modulating temperature with separate electronic apparatus (see art. T101). Suitable for systems with high and low temperature (radiators and panels) composed of 2 ball valves with thermometer and one way valve, high efficiency adjustable circulating pump ´Modulex Hybrid´ 6mt delivery, 3 way motorized mixing valve with by-pass, alignment spacer, and ball valve screw-drive adjustable for eventual substitution of pump, safety thermostat manual rest for stoppi

Predisposed for insertion of by-pass valve for eventual over pump pressure for power up to 38 KW (Art P.301.03) ** For servomotor characteristics see art. T.109.

E.627

Anticondensation preassembled module for heat generators on solid fuel feed, with thermostatic assembly

Complete of circulating pump energy class A ´Modulex Hybrid´ with 6mt delivery, anticondensation by-pass, interception valve, thermometer and check valve, wall fixing brackets. Complete of isolating shell.. Model DN 25 for power upto 32 KW: Connection 1´ - Flow KV: 3,2.

E.628

Anticondensation module for heat generators on solid fuel feed with motorized mixing valve, high efficiency adjustable circulating pump ´Modulex Hybrid´ 6mt delivery, 2 ball valves with thermometer, check valve, alignment spacer and isolating shell

E.630

Invertable relaunch module DN 32 composed of 2 ball valves with thermometer and integrated one way valve, high efficiency adjustable circulating pump ´Modulex Hybrid´ with 6mt delivery, ball valve for eventual substitution of pump and isolating shell. Suitable for power upto 125 KW - Connections: 11/4´M and 11/2´ with largening rings included.

E.631

Module bestaande uit 2 kogelkranen met verb. (Art. E.430.10), een mengventiel (Art. E.614.12) met parallel aanvoer- en retourkoppeling 1 1/2´ M. aan de boilerkant, circulatiepomp (Art. P.064), 2 kogelkranen (Art. E.608.10) met 2 thermometers, 1 controleventiel. Uitgangverloopstuk 1´ V. Ingang verb. 1´ M. Tussenafstand uitgangen 125 mm.

Dit model kan eveneens gecombineerd worden met een apparaat dat overdruk voorkomt (Art. E.615.10).

E.634

Suction valve for “Multiflex” tank with pull lever and foot valve. In brass with 1 ”M connection

Aanzuig- en retourkoppelingen: diameter 8, 10, 13 of 3/8´. Lengte aanzuigslang: 2.200 mm. Met diameter 6 koppeling, klaar voor aanhechting van niveaumeter A.040.00.

G.068

– Low temperature module applicable to manifolds, even in closets,for underfloor systems with fixed point temperature setting : 20° -50°C Complete of hydraulic separator of 2m3/h with adjustable 3 way thermostatic mixing valve, high efficiency pump Alfamax RS25/60 with adjustable 6mt delivery, reset safety thermostat for stopping the pump in case of abnomalities, check valve within closing valve, 2 themostats, 1 drain cock, 1 automatic deareator and necessary pre-assembled fittings.

Connections 1´ With connections for high temperature ¾´ KV mix:3.5

G.069

- Low temperature module applicable to manifolds, even in closets,for underfloor systems prepared for regulating modulating temperature. Complete of servomotor applied to mixing valve and prepared for connection to climatic electronic control unit (Art T.101 on page..) or other make. The module is composed of: hydraulic separator of 2 m3/h, mixing valve, adjustable high efficiency pump Alfamax RS 25/60 with 6mt delivery, reset safety thermostat for stopping the pump in case of abnomalities, one

Connection 1´ With connections for high temperature ¾´

G.080

Couple stainless steel bar manifolds AISI 304 L preassembled 1”, with ¾” Euroconus with opening valves (return) and lockshield (flow) incorporated with support brackets. Complete of n.1 manual deareator, n.1 automatic deareator and n.2 drain cocks.

G.133

V.M. Messing koppeling voor dompeltemperatuurmeethuls of voeler. Met of zonder thermometer art. E. 078.

Sheath type: length 30 mm. - internal Ø 9 mm.

G.183

Brass joint consisting of swivel metal sleeves and spigot.

G.201

Suction valve for “Multiflex” tank with pull lever and foot valve. In brass with 1 ”M connection

Aanzuig- en retourkoppelingen: diameter 8, 10, 13 of 3/8´. Lengte aanzuigslang: 2.200 mm. Met diameter 6 koppeling, klaar voor aanhechting van niveaumeter A.040.00.

G.211

Compact mixing group with fixed point thermostatic temperature control, applicable to manifolds for radiating systems, adduction connections ¾´F

Composed of: Circulation pump in energy class “A”delivery 6mt Thermostatic valve with setting 20°- 50°C Balancing lockshield One way flow valve Temperature thermometer Safety thermostat with reset for stopping the circulator in case of accidental exceeding of set temperature (in respect of European legis. 2008/125/CE) Neccessary 3 piece preset fittings for connecting manifolds N.B. manifolds are not included in the price.

G.212

Compact mixing group with fixed point thermostatic temperature control, applicable to manifolds for radiating systems, complete of hydraulic compensator, this allows self management of the system. Guarantee of an excellent delivery and flow. Adduction connections 1´M

Composed of: Steel hydraulic compensator on primary circuit of boiler with flow from 3mc/h with thickness 75mm, apt to be lodged together with the manifolds in fitted cabinets – art G.173 and G.174. Circulation pump energy class “A” 6mt Thermostatic valve setting 20° - 50°C Balancing lockshield One way flow valve 2 temperature themometers Safety thermostat with reset for stopping the circulator in case of accidental exceeding of set temperature (in respect of European legis. 2008/125/CE) Neccessary 3 piece preset fittings for connecting manifolds N.B. manifolds are not included in the price.

G.216

Compact mixing group with fixed point thermostatic temperature control, applicable to manifolds for radiating systems, underneath connections (or reversable from above) adduction connections 1´

Composed of: N.B. manifolds are not included in the price. Circulation pump energy class “A” 6mt Thermostatic valve setting 20° - 50°C Balancing lockshield One way flow valve 2 temperature themometers Safety thermostat with reset for stopping the circulator in case of accidental exceeding of set temperature (in respect of European legis. 2008/125/CE) Neccessary 3 piece preset fittings for connecting manifolds

G.220

Mixing group with climatic modulating temperature control, applicable to manifolds for heating and cooling systems radiating panels, and other types of heating and cooling sysytems, underneath connections (or reversable from above) adduction connections 1´

Composed of: N.B. manifolds are not included in the price. Circulation pump energy class “A” 6mt 4 way mixing valve Servomotor opening and closing of the mixing valve predisposed for connection to control unit (our art T.101.07 or other makes). 2 temperature thermometers 2 flow control and stop valves Air vent valve Safety thermostat with reset for stopping the circulator in case of accidental exceeding of set temperature (in respect of European legis. 2008/125/CE) Neccessary 3 piece preset fittings for connecting manifolds

G.228

Connection kit for the distribution of high temperature for integrating to mixing group Art G.216.10 and G.220.10 to be junctioned with art G.067 or to any other type of manifold. Composed of 2 control valves, isolation and special various fittings for connections.

G.230

Pre assembled compact cabinet with mixing group return and flow manifolds for radiating heating systems with thermostatic fixed point low temperature control with or without manifolds for heating components at high temperatures (towel dryers, radiators etc).

Composed of: Mixing group art G.211.10 Couple manifolds Art g.081 complete of: Connection of lockshields ¾´ euroconus Valves for the application of electtric actuators Flow regulators Automatic deareator Drain cocks Support brackets High temperature manifolds, if planned for Container cabinet Art G.174 See dimensions in table

G.235

Pre assembled compact cabinet with mixing group return and flow manifolds for radiating heating systems with thermostatic fixed point low temperature control, complete of hydraulic compensator, this allows self management of the system. Guarantee of an excellent delivery and flow with or without manifolds for heating components at high temperatures (towel dryers, radiators etc).

Composed: Mixing group art G.212.10 equipped with hydraulic compensator Couple manifolds Art g.081 complete of: Connection of lockshields ¾´ euroconus Valves for the application of electtric actuators Flow regulators Automatic deareator Drain cocks Support brackets High temperature manifolds, if planned for Container cabinet Art G.174 See dimensions in table

G.240

Pre assembled compact cabinet complete of mixing group for modulating climatic temperature control, and for manifolds for heating and cooling systems radiating panels, and other types of heating and cooling systems, adduction connections 1´F (from underneath or reversable from above).

Composed: A) Mixing group Art G.220.10 complete with 4 wat mixing valve motorized three points controllable by a climatic control unit non included. B) Couple manifolds Art g.081 complete of: Connection of lockshields ¾´ euroconus Valves for the application of electtric actuators Flow regulators Automatic deareator Drain cocks Support brackets High temperature manifolds, if planned for Container cabinet Art G.174 See dimensions in table

G.851

Straight brass fitting with F thread end and compression end for multilayer pipe.

G.852

Straight brass fitting with M thread end and compression end for multilayer pipe

G.853

ntemediate straight brass comp. fitting for multilayer pipe.

G.854

Intermediate elbow brass compresion fitting for multilayer pipe.

G.855

Elbow brass fitting with M thread end and compression end for multilayer pipe

G.856

Elbow brass fitting with F thread end and compression end for multilayer pipe.

G.858

Elbow brass fitting with F thread end and 3 holed flange and compression end for multilayer pipe.

G.860

´T´ brass fitting with central F thread end and compression end for multilayer pipe.

G.862

Intermediate T brass compression fitting for multilayer pipe.

G.864

Brass elbow fitting with M thread end and compression end for multilayer pipe.

G.866

Reduced intermediate ´T´ brass compression fitting for multilayer pipe.

G.917

Straight brass fitting with F swivel nut and press fitting end for multilayer and polythene pipe.

Suitable for connections to manifolds; G.015-G.016-G.019-G.020-G.021-G.022-G.023-G.024-G.025-G.026-G.030-G.031-G.033.

H.100

Electronic programmer with liquid crystal display, double irrigation and interative programm.

Technical data: Irrigation time from 1 min to 8 hours (1 min increment) Flexible scheduling: - Daily - Weekly - Even / odd day watering - Irrigation at intervals of 1 to 30 days Activation / Deactivation of the rain sensor Input power: - 220 VAC - (0.625 A) Output power: - Maximum per station: 24 VAC- (0.25 A) - Maximum for total (including MV control: 24 VAC- (0.625 A) Operating temperature: -10 ° to 60 ° C

H.490

Solenoid valve in PVC plastic resistant to UV rays and corrosion with stainless steel screws. Servo assisted diaphram type.

With manual operating valve. Slow closing. Tension 24VCA - 50Hz Absorption 0,20Amp.

H.500

Messing elektroventiel, normaal uit. Type met servobestuurd diafragma.

Min. operationele differentiële druk 0.1 bar. Max. Temperature 90°C. Geschikt voor toepassingen met lucht en water. Alternerende netstroomtoevoer. Elektrische koppeling via DIN 43650.

H.501