Antares Pipes

Suction valve for “Multiflex” tank with pull lever and foot valve. In brass with 1 ”M connection

Aanzuig- en retourkoppelingen: diameter 8, 10, 13 of 3/8´. Lengte aanzuigslang: 2.200 mm. Met diameter 6 koppeling, klaar voor aanhechting van niveaumeter A.040.00.

E.363

Suction valve for “Multiflex” tank with pull lever and foot valve. In brass with 1 ”M connection

Aanzuig- en retourkoppelingen: diameter 8, 10, 13 of 3/8´. Lengte aanzuigslang: 2.200 mm. Met diameter 6 koppeling, klaar voor aanhechting van niveaumeter A.040.00.

E.365

Suction valve for “Multiflex” tank with pull lever and foot valve. In brass with 1 ”M connection

Aanzuig- en retourkoppelingen: diameter 8, 10, 13 of 3/8´. Lengte aanzuigslang: 2.200 mm. Met diameter 6 koppeling, klaar voor aanhechting van niveaumeter A.040.00.

F.080

Pack of 1kg solder rods for metal. Length 400*diam 9mm Low melting point.

F.083

1 kg pack of stearine.

Deoxider to solder pipe joints in lead brass copper iron zinc. Makes soldering easier. Pack 10 rods.

F.086

Coil of 250g soldering wire at low temperature.

F.088

flux and deoxidiser gel for soft soldering of material in copper bronze lead steel and stainless steel.

Used especially for soldering of copper fittings for domestic and industrial water systems of piping for heating , gutters, radio and TV appliances.

F.090

Pack of 100 g. of alloy sticks for soldering

F.092

Pack of 500g of powdered deoxidiser.

For strong soldering at high temp. of copper pipe for gas and water to be used with alloy for strong soldering with silver on copper, copper alloy, steel.

F.280

- refractory adhesive suitable for temp.upto 1100°C. Immediate and solid adhesion.

Zuurstofonttrekker om buisverbindingsstukken in lood, messing, koper, ijzer en zink te solderen. Vergemakkelijkt het solderen. Verpakking van 10 stangen.

F.282

- refractory sealant classified REI 180 suitable for rapid cementing, no smell for temp. upto 1100°C.

Adheres to a vast number of supports even damp concrete plaster metal wood. 500gr cartridge

F.295

Pack of 2 white fixing collars for smoke pipes complete with 2 dowles 2 screws 6 nuts and 2 adjustable spacers Collar length mm 25*1,5.

F.296

Pack of 10 stainless steel collars, adjustable in diam. for fixing of smoke pipes. Complete with screws dowles 8*40 and adjustable spacers. Collar band 0,5*18. Adjustable distance from wall 60/100.

F.297

Zwaar verzinkte buisclip met gesoldeerde moer. Clipdikte 2.5 mm.

F.620

Pipe cutter for diameters 3 to 35 mm.

F.664

Amalgamating protective tape for the parts of the pipe where the external sheath has been removed in order to allow joint . Regulation forsees that these parts must be covered with yellow protective tape

Width 25mm Thickness 0,5mm Length 5mt.

F.665

Polyvinilic black adhesive tape suitable for small repaires on isolating sheath Of pipes with thermal insulation (Art E.342 and E.343) during installation of solar systems.

Width : 19 mm Thicknes 0,18 mm Length 20 mt

F.668

Adhesive tape in foamed reinforced rubber with black close cells and throaway protection film.

Suitable for the insulation of hot and cold pipes, in particula for the cooling production and distribution systems and for special parts that cannot be insulated with tubular pipe insulators. Thickness 3mm.

F.730

Verpakking van 10 afsluitdoppen voor rookkanalen en gasrookvoeler met silicone afdichtring en vijzen.

F.745

Flaring instrument for corrugated pipe for templates F.746.12 - F.746.15 and F.746.20 for diameters from 1/2´- 3/4´ e 1´.

This device facilitates the forming of flaring without having to fall back on N°3.

F.746

Templates for inserting inside the flaring instrument F.745.10.

F.748

Suitcase kit for corrugated pipe CSST complete of: Case in ABS - Pipe-cutter F.620.35 - Flaring instrument F.745.10 - Templates for flaring instrument F.746.12 F.746.15 and F.746.20 - n20 nuts 1/2´ - n20 open rings diam.12 with n10 washers Fasit and n10 washer in NBR - n12 nuts 1´ - n12 open rings diam.20 with n6 washers in Fasit and 6 washers in NBR.

Complete with: ABS case - Pipe cutter Art. F.620.28 - Flaring unit Art. F. 745.10, templates for flaring machine Art. F. 746.12 and F. 746.15 and F.746.20 - n ° 20 1/2 ´nuts, n ° 20 open rings Ø 12 with n ° 10 Fasit seals and n ° 10 NBR seals, n ° 20 3/4 ´nuts - n ° 20 open rings Ø 15, with n ° 10 Fasit seals and n ° 10 NBR seals , n ° 12 1 ´nuts, n ° 12 open rings Ø 20 with n ° 6 gaskets in Fasit and n. ° 6 gaskets in NBR.

G.134