Antares Pipes

Stainless steel Inox PN 12 expansion socket with inside sleeve.

Connections: solder socket ends. Absorption Capacity: 25 mm (10 mm traction, 15 mm compression).

Vibration-damping expansion joint for gas burner pipe feeders with stainless steel centre bellows & loose flanges in PN 16 UNI2223 steel. Can also be used as expansion socket. In accordance with UNI CIG 8042.

E.338

Flexible hose kit from 220 mm to 440 mm in stainless steel for connection of gas boilers.

Compoesed of: - N. 1 plastified flex yellow DN20, connect. 3/4´ F sw. x 3/4´M for gas with NBR washer, in accordance with EN549. - N. 2 flex hoses DN20 conn. 3/4´F sw. x 3/4´M for hot water heating with Fasit washer. - N. 2 flex hoses DN12 conn. 1/2´F sw. x 1/2´M for hot sanitary water with Fasit washer.

E.340

Coil of corrugated flexible pipe CST (Corrugated Stainles Steel tubing) in stainless steel AISI 316 ´INOFLEX´ with paralle spiral coils for flow of drinkable water and domestic. Can be cut to measure without any particular tool and connect with the fittings E.346 - E.348 - G.147 - G.149 - G.167 - G.158

Thickness 0.3 mm. Max temp 550°C max pressure 15 bar.

E.341

Coil of corrugated flexible pipe CSST (Corrugated stainless steel tubing) in stainless steel AISI 316 ´INOFLEX´ parallel spiral coils with protective yellow sheath (MDPE) suitable for gas systems, conforming with leg. EN15266. Can connect with the fittings below.

Thickness 0.3 mm Max temp. 100°C max pressure 0.5 bar.

E.342

Coil of flexible tube ´INOFLEX CSST´ for solar systems. In stainless steel AISI 304 corrugated parallel spires thickness 0,3mm in defined length with isolating expanding sheath EPDM 13 mm and coated with protective film against UV rays and from ware and tare with or without multiphase cable for temp. probes.

Max temp: - 40 + 150°C - presure PN 15bar.

E.345

Double pipe (outward and return) of “INOFLEX CSST” flexible hose for solar systems, in AISI316L stainless steel corrugated with parallel coils, thickness 0.3 mm. in the defined length with 13 mm PES insulation covering and externally covered with protective film from UV rays and mechanical wear, with multiphase cable for the temperature probes. -

Operating temperatures -60°C/+150°C (180°C Peak)

E.346

Pack of brass nuts for the washers with corrugated tube CSST.

With the half ring and the fittings with male thread with flat seat allows you to form a joint.

E.348

Pack of open rings (2) with washers (3) for fastening fitting joints assemblies with corrugated pipe CSST.

Thickness washers 1.8 mmm. Note: when buying bear in mind the use, european legislation foresees the obligation to use gas washers in NBR EN682.

E.349

Double pipe corrugated hose ´KLIMA CSST´, ready to be laid underground for heat pumps, biomass powered heating systems and technological uses, in stainless steel AISI 304, thickness 0,3 in the length defined on the table with low thermal conductivity nanotechnological aerogel insulation coating: 0,017 W/mK @ 10 °C. With UV protective wrap - Can be directly laid underground.

Maximum operating temperature: 200 °C. Pressure PN 15 bar.

E.350

Open ring nut set with sealing gasket for the formation of connection fittings with CSST corrugated hose.

Gasket thickness: 1.8 mm. Note: When purchasing, consider the specificity of use: European regulations require that gaskets made of NBR are used for gas, in accordance with EN 682.

E.360

Quick brass fitting with male thread for corrugated inox pipe.

Composed of joint, nut, cut washer and N°2 specified O-ring.

To view prices, log in

Pipes

CONTACTS

Italia

ANTARES for Water & Fire Srl

WHO ARE WE