Antares Pipes

Pack of 4 anti vibration supports for insulation of heat pumps, generators, air conditioners and pumping groups with screws and bolts. Can be used on wall brackets or ground supports.

Anti vibration supports for heat pumps, generators and air conditioners.

F.390

Pack of 4 anti vibration supports for insulation of heat pumps, generators, air conditioners and pumping groups. Can be used on ground supports.

Anti vibration supports for heat pumps, generators and air conditioners.

W.153

Pack of 5 fittings with compression ends and M. threaded ends, made of nipples, F. nut and brass compression olive for the connection of capillary tubes.

W.150

Pack of 5 fittings with male connection and brass compression olive for the connection of capillary tubes (from the fuel pump to the solenoid or to the nozzle, for the connection of gas to the pilot burners and other).

G.816

Pack of 5 sheets 1.000x 2.000mm of soldered mesh with 3mm wire for layers of cement Mesh sizes 100x100mm

G.822

Pack of 50 pipe guides suitable for the laying down of pipe with distance of 6cm. The holes on the base allow for further fixing to the insulation with the use of special modular clips.

G.831

Pack of 500 manual pipe clips.

For manual fixing OF PIPES TO INSULATION PANELS UP TO DIAM 20 and also for fixing of pipe guides art G.822 45mm high. The insulator must have a minimun thickness of 30mm.

G.830

Pack of 500 wire mesh fixing clips for application to insulation panels 28mm high. Distance between points 75.

E.346

Pack of brass nuts for the washers with corrugated tube CSST.

With the half ring and the fittings with male thread with flat seat allows you to form a joint.

E.348

Pack of open rings (2) with washers (3) for fastening fitting joints assemblies with corrugated pipe CSST.

Thickness washers 1.8 mmm. Note: when buying bear in mind the use, european legislation foresees the obligation to use gas washers in NBR EN682.

H.162

Pack of ten plastic fittings with T deviation diam 16*16*16 Self threading to fit sprinkler hose.

F.625

Pipe cutter for multilayer and polythene pipe for diameters up to 16-20-26.

G.840

Pipe dispenser.

G.939

Pliers with TH profile for pressers Art G.935.00 and G.937.00.

G.760

Polyethylene pipe bend former.

F.665

Polyvinilic black adhesive tape suitable for small repaires on isolating sheath Of pipes with thermal insulation (Art E.342 and E.343) during installation.

Width : 19 mm Thicknes 0,18 mm Length 20 mt

G.800

Quantities as indicated below of insulation heating panels for underfloor heating systems ´CLASSIC FLOOR´ in polystyrene with anti-steam film in polyethylene 0.15mm and depth of trail for pipe 16/17 Borders male /female for fitted layout.

Conductivity 0,0332W/mK Load resistence: 10% deformatio: KPA 200

E.365

Quick brass fitting with connection for corrugated steel hose and copper hose.

Composed of joint, nut, cut washer and N°2 specified O-ring, ogive for copper pipe.

E.363

Quick brass fitting with female thread for corrugated steel hose.

Composed of joint, nut, cut washer and N°2 specified O-ring.

E.360

Quick brass fitting with male thread for corrugated inox pipe.

Composed of joint, nut, cut washer and N°2 specified O-ring.

E.800

Rod in PVC 2 mt diam 50 mm.

G.818

Roll of PE polyethylene sheet 100m long and 1,5m in hight when folded is used to place over flat insulation panel (art G.810.20) used as a stern barrier; suitable for radiant systems with soldered mesh or fixing materials.

B.124

Safety tube.

Safety tube for all types of gas. Internal and external in steel with connecting cap DIN 3383 for connection to all types of safety valves or taps. Connection 1/2´ F.

G.930

Spring to bend multilayer pipe.

E.330

Stainless steel extensible flexible hose AISI 316 accordance with leg. UNI 11353, approved for connections with solar of water or water systems . Max pressure 10 bar. Max temp. 150°C. Complete with washers. .

Max. pressure: 10 bar - Max. temperature: -20°C to +110°C.

E.335

Stainless steel Inox PN 12 expansion socket with inside sleeve.

Connections: solder socket ends. Absorption Capacity: 25 mm (10 mm traction, 15 mm compression).

G.167

Straight brass fitting between the copper tube and the corrugated steel tube.

G.917

Straight brass fitting with F swivel nut and press fitting end for multilayer and polythene pipe.

Suitable for connections to manifolds; G.015-G.016-G.019-G.020-G.021-G.022-G.023-G.024-G.025-G.026-G.030-G.031-G.033.

F.748

Suitcase kit for corrugated pipe CSST complete of: Case in ABS - Pipe-cutter F.620.35 - Flaring instrument F.745.10 - Templates for flaring instrument F.746.12 F.746.15 and F.746.20 - n20 nuts 1/2´ - n20 open rings diam.12 with n10 washers Fasit and n10 washer in NBR - n12 nuts 1´ - n12 open rings diam.20 with n6 washers in Fasit and 6 washers in NBR.

Complete with: ABS case - Pipe cutter Art. F.620.28 - Flaring unit Art. F. 745.10, templates for flaring machine Art. F. 746.12 and F. 746.15 and F.746.20 - n ° 20 1/2 ´nuts, n ° 20 open rings Ø 12 with n ° 10 Fasit seals and n ° 10 NBR seals, n ° 20 3/4 ´nuts - n ° 20 open rings Ø 15, with n ° 10 Fasit seals and n ° 10 NBR seals , n ° 12 1 ´nuts, n ° 12 open rings Ø 20 with n ° 6 gaskets in Fasit and n. ° 6 gaskets in NBR.

F.746