Made up of steel spirals with metallic net sheath and another protective plast sheath DN12. Complete with washers for gas.

Safety tube for all types of gas. Internal and external in steel with connecting cap DIN 3383 for connection to all types of safety valves or taps. Connection 1/2´ F.

Max. Pressure: 6 bar - Max. Temperature: from - 40° C / + 550° C.

Max working pressure: 15 bar. Max temp. from -40°C to +150°C

Certified for installation on drinkable water systems. Max temp 10-105C° Absorption capacity 22 mm compression 6 mm .Possible displacement 22 mm.

Certified for installation on drinkable water systems. Max temp. 10-105C°.

Max. pressure: 10 bar - Max. temperature: -20°C to +110°C.

Connections: solder socket ends. Absorption Capacity: 25 mm (10 mm traction, 15 mm compression).

Compoesed of: - N. 1 plastified flex yellow DN20, connect. 3/4´ F sw. x 3/4´M for gas with NBR washer, in accordance with EN549. - N. 2 flex hoses DN20 conn. 3/4´F sw. x 3/4´M for hot water heating with Fasit washer. - N. 2 flex hoses DN12 conn. 1/2´F sw. x 1/2´M for hot sanitary water with Fasit washer.

Thickness 0.3 mm. Max temp 550°C max pressure 15 bar.

Thickness 0.3 mm Max temp. 100°C max pressure 0.5 bar.

Max temp: - 40 + 150°C - presure PN 15bar.

Operating temperatures -60°C/+150°C (180°C Peak)

With the half ring and the fittings with male thread with flat seat allows you to form a joint.

Thickness washers 1.8 mmm. Note: when buying bear in mind the use, european legislation foresees the obligation to use gas washers in NBR EN682.

Maximum operating temperature: 200 °C. Pressure PN 15 bar.

Gasket thickness: 1.8 mm. Note: When purchasing, consider the specificity of use: European regulations require that gaskets made of NBR are used for gas, in accordance with EN 682.

Composed of joint, nut, cut washer and N°2 specified O-ring.

Composed of joint, nut, cut washer and N°2 specified O-ring.

Composed of joint, nut, cut washer and N°2 specified O-ring, ogive for copper pipe.

Anti vibration supports for heat pumps, generators and air conditioners.

Anti vibration supports for heat pumps, generators and air conditioners.

Anti vibration supports for heat pumps, generators and air conditioners.

Tube Cutter with Cutting Wheel – Cutting Capacity 3–35 mm

Width 25mm Thickness 0,5mm Length 5mt.

Width : 19 mm Thicknes 0,18 mm Length 20 mt

Suitable for the insulation of hot and cold pipes, in particula for the cooling production and distribution systems and for special parts that cannot be insulated with tubular pipe insulators. Thickness 3mm.

This device facilitates the forming of flaring without having to fall back on N°3.

Complete with: ABS case - Pipe cutter Art. F.620.28 - Flaring unit Art. F. 745.10, templates for flaring machine Art. F. 746.12 and F. 746.15 and F.746.20 - n ° 20 1/2 ´nuts, n ° 20 open rings Ø 12 with n ° 10 Fasit seals and n ° 10 NBR seals, n ° 20 3/4 ´nuts - n ° 20 open rings Ø 15, with n ° 10 Fasit seals and n ° 10 NBR seals , n ° 12 1 ´nuts, n ° 12 open rings Ø 20 with n ° 6 gaskets in Fasit and n. ° 6 gaskets in NBR.

For central & underfloor heating systems, hot & cold water distribution systems. Pressure: 6 bar. Temp.: 95° C. (10 bar and 70 ° C.). D

For hot & cold water distribution systems, underfloor heating & radiator systems. Pressure: 10 bar. Temperature: 95° C.

For hot & cold water distribution systems, underfloor heating & radiator systems. Pressure: 10 bar. Temperature: 95° C.

Conductivity 0,0332W/mK Load resistence: 10% deformatio: KPA 200

Height 150mm .Thickness 6mm . Eliminates heat dispersion and absorbs floor dilation. For application on perimeter of walls before laying down screed. Polyethylene sheet to put over the insulator to avoid accedental dripping of cement between floor and wall. According to current norms allows for screed dialation of 5mm (Din 18560).

When added to cement mix guarantees even covering of pipework. To be diluited before using in the ratio of 1.3 Kg. to 100 Kg. cement.

Conductivity 0,0332W/mK Load resistence: 10% deformation: KPA 200

Dosing: 600 gr. for cubic meter of cement.

Ensure the lifting of 30mm of the mesh from the bottom and distance between the two wire meshes (60mm) and the pipes.

For manual fixing OF PIPES TO INSULATION PANELS UP TO DIAM 20 and also for fixing of pipe guides art G.822 45mm high. The insulator must have a minimun thickness of 30mm.

For the automatic insertion of pipe fixing clips. Art G.836 and G.828.20.

Suitable for automatic fixing of pipes up to diam 20mm onto insulation panels with special tool ´Tacker´ art G.835.00 and also for fixing of pipe guide art G.822.

For hot and cold water distribution systems, radiator systems & underfloor heating. Pressure: 10 bar. Temperature: 95°C. SKZ certificate No. A-270.

For the distribution of hor and cold water, radiator heating systems and underfloor heating. Pressure 10bar. Temperature: 95°C.

For the distribution of hot and cold water, radiator heating sytems and underfloor heating. Pressure 10bar temp. 95°C.

For the distribution of hot and cold water, radiator heating systems and underfloor heating. Pressure 10 bar temp. 95°C.

For the distribution of hot and cold water, radiator heating systems and underfloor heating. Pressure 10 bar temp. 95°C.

Suitable for connections to manifolds; G.015-G.016-G.019-G.020-G.021-G.022-G.023-G.024-G.025-G.026-G.030-G.031-G.033.

Run on electricity. Pliers with TH profile. 230 V.

Battery or elecrticity 230v powered :Pliers with TH profile: Complete with battery, battery charger and power cable.

External dimensions: height 90 mm., depth 40 mm. Can contain pipes up to diameter 22 mm. Resistant to temperature, maximum: 100°C.